Ordinary concrete electronic thermometer(0.1Resolving power)Instructions
【2011edition】
１、Open the battery cover at the back，take4section7Dry cell No.，Polarity of attention，Ensure good contact with spring plate in battery box。(here，If the battery is installed correctly，When pressed“lighting”Button time，The light at the top should be on.。Otherwise, check whether the battery polarity is reversed or in poor contact.。)
２、Press down“measure”Button，The device should have a display。If the sensor is not plugged in，设备display“ □ □”；If a sensor is inserted，The device should display the temperature value of the sensor。
３、How to insert a sensor？Insert the two plugs of the same sensor into the two sensor sockets at the bottom of the device，Do not distinguish polarity，Hold on for a few seconds，When the displayed value is stable。(Do not touch the metal part of the sensor plug by hand)。
４、LEDTemperature value displayed on the screen，Records need to be copied manually，For later use。
５、The same way，Plug in the two plugs of the other sensor，Take the next measurement。
６、If the sensor is not inserted on the device，设备display“ □ □”，If kept1More than minutes，The device will shut down automatically(Automatic power failure)。
７、If it is pressed again after power failure“measure”Button，The device will power up again。
８、There is one on the panel of this thermometer“lighting”Button，Press this key.，This thermometer can be used as a temporary flashlight，However, it is recommended not to use the flashlight function during the measurement.，So as not to affect the accuracy。
９、The sensor used in this thermometer is“Win the world”General purpose sensor，If an incompatible sensor is used，May cause large error or damage to equipment。
book《Instructions》Only applicable to2011General electronic thermometer for concrete
This product is designed for low price users，No memory function，Display only。
* LEDdisplay，Adapt to a wide range of ambient temperature；
* Built in automatic error correction circuit；Ensure measurement accuracy；
* measuring range：－30～110℃； Resolving power0.1℃；
“Win the world®”It is the registered trademark of Jinan huanyutong Technology Co., Ltd.。Provide users with various concrete temperature measuring equipment，Include：Real time monitoring type、Time recording type、Portable recording type、General temperature measurement and other series products。Company product website：http://www.0531hyt.com，Welcome to visit。
Win the world® General electronic thermometer
Application instance
☆ Ordinary portable,Display the temperature of the measured sensor。Is the most common product，This product satisfies customers“Temperature measurement and display”Basic Requirements，It is especially suitable for products with low requirements for other functions.，Users with low budget requirements。If users need intelligent concrete temperature measurement system，Please visit our websitehttp://www.0531hyt.com，There are many models for you to choose from。
Win the world®General portable electronic thermometer（ＰＸ）Use process instance
Welcome to win®General portable electronic thermometer（ＰＸ）（Hereinafter referred to aspxThermodetector）。Let's take a look at an example。
Before that，Please press to read carefully《Instructions》Etc.；And confirmpxThe battery box of the thermometer is installed with the required７＃Battery。
Using examples１：
Step one：Bundling sensor。
When binding the reinforcement, bind the sensor according to the temperature measurement point set in the temperature measurement scheme.，Or inhThe temperature measuring points set on the type steel bar according to the temperature measurement scheme are bundled with sensors.，Insert preset points before concreting，fixed。
Normally，Multiple temperature measuring points on a plane，Each temperature measuring point has3~8Sensor，Elevation as figure：
（Elevation layout of each sensor of a plane temperature measuring point）
Step two：Sensor number and group。
number：Number field sensors。Hypothetical co ownershipNMonitoring points。Set the sensor number of the top elevation point on the first plane point as1，Down in order2，3，4，Then the sensor number of the last elevation point on the second plane point is the number of the last elevation point immediately following the first plane point.5，Down in order6，7，8；……The last elevation point to the last plan point is numberedN。
Grouping：You can group sensors from the same elevation point into the same group，For example, in the figure above１＃～４＃Sensor is the first group，５＃～８＃Sensors are the second group, etc.，Grouping is to facilitate the recording and comparison of temperature differences（In the smart version，These jobs are automatic）。
Step three：Data collection。
After concrete pouring3-5Hour to start the first data acquisition，Interval time２～４hour。
1、 Please confirm before the first usepxThermodetectorThe battery is properly installed；
2、 take1Two pins of No. 1 sensor are respectively inserted into two sensor sockets of the recorder（Positive and negative poles）；
Press the“measure”Button，Display the number of current measurements，Record the sensor number manually、Date time and temperature value。
3、 frompxThermodetectorOut of the sensor socket1Sensor number，Again2Sensor numberTwo pins ofpxThermodetectorTwo sensor sockets for。Repeat the above。
4、 …AgainnSensor numberTwo pins of are respectively inserted into two sensor sockets of the recorder.。Repeat the above，Make manual records。
Step four：useexcelTabulation and data processing。
1、 DependentexcelformReference resourcesPlease download the document at：
http://www.0531hyt.com/cewen/xls/；
２、Fill the data into the form you have designed，Then inexcelCall the built-in drawing function in the table。